ITHSEN WB-1. Coming soon.
USB 3.0 hardware write blocker
The ITHSEN WB-1 is a hardware write blocker for USB storage. It sits between an evidence drive and the examiner's computer, lets read commands through and refuses every command that could change the drive. It is read-only by construction: there is no write mode and no switch.

Specifications
What it is.
Everything it does, and everything in the box.
- Model
- ITHSEN WB-1
- Function
- Hardware write blocker for USB mass storage
- Operating mode
- Read-only. No write mode.
- Evidence port
- USB 3.0 Type-A (drive side)
- Computer port
- USB 3.0 Type-B (workstation side)
- Power
- USB-C, 5 V DC / 3 A, adapter supplied
- Status lights
- 7: DRIVE, READ ONLY, FAULT, PC, WRITE BLOCKED, FAULT, POWER
- Enclosure
- 107 x 87 x 26 mm, no visible screws
- In the box
- Write blocker, power adapter, USB-C power cable, USB 3.0 A-B cable, quick start card, test certificate, warranty card
- Origin
- Designed and made in India
Write rejection test
- test checks passed
- 26/26
- modifying commands refused
- 24/24
- bytes written to the drive
- 0
Lab test on a Windows 11 workstation, November 2026. Every production unit ships with its own test certificate.
Status lights
Seven lights, left to right.
Green is normal, yellow asks for attention, red is a fault. WRITE BLOCKED flashing is normal: computers often try to write to a drive when it is connected. Each flash is one write command that was refused.
DRIVE
Evidence side
On: drive ready. Blinking: reading.
READ ONLY
Evidence side
On: write protection is running.
FAULT
Evidence side
Evidence-side fault. Stays on until power is removed.
PC
Computer side
On: recognised by the computer. Blinking: transfer.
WRITE BLOCKED
Computer side
Flashes each time a write command is refused.
FAULT
Computer side
Computer-side fault. Stays on until power is removed.
POWER
Device
On: the device is powered.
In use
Five steps from seized drive to verified image.
- 01
Connect the supplied 5 V / 3 A adapter to the USB-C port. POWER and READ ONLY light up.
- 02
Connect COMPUTER to your workstation with the supplied USB 3.0 cable. PC lights up.
- 03
Connect the evidence drive to EVIDENCE. DRIVE lights up when the drive is ready.
- 04
Acquire the image with your forensic software and verify the hash values.
- 05
When finished, eject the drive in the software, unplug the drive, then remove power.
Do not connect evidence unless READ ONLY is lit.

Software to match
ITHSEN Imager
ITHSEN Imager makes a bit-for-bit copy of an evidence drive, proves the copy with SHA-256 and writes the report for your case file. It is designed alongside the WB-1 and works with other hardware write blockers too.
See what Imager doesGuides
New to write blockers, or comparing options?
Questions
About the WB-1.
How does the ITHSEN WB-1 block writes?
The WB-1 sits between the evidence drive and the computer and checks every command twice. Read commands are passed on. Commands that would modify the drive are refused and the computer is told the medium is write protected. The device has no write mode at all.
Can the WB-1 be switched to read/write mode?
No. The WB-1 is read-only. It has no write mode, no switch and no write path in its hardware or firmware.
Which drives does the WB-1 work with?
The WB-1 is built for USB mass storage: USB flash drives, memory cards in a USB card reader, and external USB hard drives and SSDs. Connect the drive to the USB 3.0 Type-A evidence port.
How fast is the WB-1?
The WB-1 runs SuperSpeed USB 3.0 on both the evidence and computer sides, ten times the bandwidth of a USB 2.0 write blocker. A large drive that takes all night on USB 2.0 is done in a fraction of the time.
How is the WB-1 tested?
We test the WB-1 against the commands a computer can send to change a drive: write, erase, format, settings changes and more. In our lab test all 24 modifying commands were refused and not one byte reached the drive. Every production unit ships with its own test certificate.
Is the WB-1 an affordable forensic write blocker?
Yes. The WB-1 does one job, read-only access to USB storage, and leaves out screens, extra interfaces and built-in imaging that raise the price of larger units. It is designed and made in India so that labs, police units, trainers and students here can buy and get support locally. Pricing will be announced at launch.
When can I buy the WB-1?
The WB-1 is coming soon. Email contact@shopdibz.com to be first to hear about launch and pricing.
Is the WB-1 made in India?
Yes. The WB-1 is designed and made in India by Shopdibz Pvt Ltd, Trivandrum, Kerala.
Contact
Want one on your bench when it ships?
Tell us who you are and what you image. We will write when the WB-1 is ready. Labs, agencies, trainers and distributors welcome.